Temperature measuring digital panel meters

The meters and controllers on this page accept such sensors as thermocouoples, 2 wire and 3 wire PT100s etc. All can be easily set to read in ^oC or ^oF, with various levels of precision and resolution..

Suited for these applications and more:-

• Controlled environment temperature measurement
• Engine test measurements (inlet, combustion, bearing and exhaust)
• Chemical reaction temperature monitoring
• Curing temperature monitoring
• Cold-room monitoring
• etc...

This page has 2 types for you to choose from:-

[INT-T display] [PICA-T miniature display]

[^] Model INT-T
The INT-T is a low cost yet highly flexible and easy to use 1/8 DIN temperature meter. It accepts a wide range of thermocouple and PT100 sensor types.. It has a number of useful plug-in options which make it ideal for use in many control and monitoring applications.
See operating Manual
See datasheet
Model number and price calculator
INT-T Specifications
Input connections	2 wire thermocouple or 3 wire PT100
Input Signal	The following sensors are supported... Sensor Accuracy Max. Resolution Type J +/-0.5oC 0.1oC Type K +/-0.6oC 0.1oC Type T +/-0.3oC 0.1oC Type N +/-1.0oC 0.1oC Type R +/-1.0oC 0.1oC Type S +/-1.0oC 0.1oC PT100 DIN +/-0.2oC 0.1oC PT100 ANSI +/-0.2oC 0.1oC
PT100 Excitation	300 micro-amperes
Digits	5 digits, 14mm high. Legible up to 7 metres away
Digit colour	Red or green
Scaling	Fixed linearisation tables for each sensor. Simply select oC or oF and 1 degree or 0.1 degree resolution. Digital UP/DOWN trimming of zero reading
Filtering	Adjustable 0 to 5 Seconds
Last digit Round-up	not available on this model
User linearisation	Linearisation fixed for each sensor type.
Front panel controls	Calibration, Reset, Max/Min, Alarms
Power	11-30VDC or 95-265 VAC
Accuracy	Depends on sensor type. See 'Input signal' above
Thermal stability - range	+/- 50ppm/oC.
Thermal stability - offset	0.05DegC/C for T/C, 20ppm/C for PT100
Analogue output	Optional plug-in module 4-20mA into 0 to 500 Ohms 0-10V into loads>600 Ohms -5 to+5V into loads>600 Ohms Fully isolated from input and power Fully scalable with digital precision Forward and reversion action possible
Alarm output	Optional plug-in modules 2 Alarms rated 5A 250VAC, SPST 4 Alarms rated 5A 250VAC, SPST Adjustable hysteresis Energise or de-energise on trip Normally open or closed
Serial data output	Optional plug-in modules. RS232 1200 baud output only. RS422 1200 baud output only. RS485 Addressable DeviceNet Addressable Modbus Addressable Profibus DP Addressable
Logic inputs	TARE, Peak/Valley and RESET
Connectors	Detachable screw terminals
Bezel size	96mm wide x 48mm high. 13mm forward.
Panel cutout	92mm wide x 45mm high. +1mm, -0mm
Depth behind panel	125mm including connectors + cable.
Sealing	IP65 standard, IP67 with optional SPC4 cover

[^] Model PICA-T
The PICA-T is a low cost yet highly flexible and easy to use miniature 1/32 DIN temperature display for display-only applications.
Input connections	Thermocouple and 3 wire PT100
Input Signals	Thermocouple types J, K and T PT100 RTD 3 wire
Excitation	<1.3mA for PT100 sensors
Digits	4 digits, 10mm high. Legible up to 5 metres away.
Digit colour	Red
Scaling	Digital 3 button programming system
Filtering	Not available on this model
Last digit Round-up	Not available on this model
User linearisation	Not available on this model
Front panel controls	3 programming buttons
Power	11-70VDC & 21-53VAC or 100-300VDC & 85-265 VAC
Accuracy	+/-0.1% of range +/-3 digits
Thermal stability - range	+/- 100ppm/oC
Thermal stability - offset	+/- 100ppm/oC
Analogue output	Not available on this model
Alarm output	Not available on this model
Serial data output	Not available on this model
Logic inputs	Not available on this model
Connectors	Detachable screw terminals
Bezel size	48mm wide x 24mm high. 13mm forward.
Panel cutout	45mm wide x 22mm high. +1mm, -0mm
Depth behind panel	70mm including connectors + cable.
Sealing	IP65
See datasheet
See manual